yyw_articles

Home > 
  • yyw_articles
  • Carbon battery.Working principle of lithium battery protection circuit, lithium battery protection c

    Time:2024.12.06Browse:0

    Share:

      

      Lithium battery protection circuit working principle, lithium battery protection circuit design. The reason why lithium battery (rechargeable type) needs protection is determined by its own characteristics. Since the material of the lithium battery itself determines that it cannot be overcharged, overdischarged, overcurrent, short-circuited, or charged and discharged at ultra-high temperatures, lithium batteries always appear with a delicate protective board and a current fuse.

      Lithium battery protection circuit working principle

      The protection function of lithium batteries is usually completed by the protection circuit board and PTC. The protection board is composed of electronic components. It accurately monitors the voltage of the battery core and the current of the charge and discharge circuit at all times in an environment of -40°C to +85°C, and controls it in a timely manner. On and off of the current loop; the main function of PTC is to protect the battery in high temperature environments and prevent battery combustion, explosion and other vicious accidents.

      The protection circuit usually consists of control IC, MOs switch tube, fuse, resistor, capacitor and other components, as shown in Figure 2. Under normal circumstances, the control IC output signal controls the MOs switch tube to conduct, so that the battery core is connected to the external circuit. When the battery core voltage or loop current exceeds the specified value, it immediately controls the MOS tube to turn off to protect the battery core. Safety.

      1. Normal state

      Under normal conditions, the "CO" and "DO" pins of N1 in the circuit both output high voltage, and both MOSFETs are in the on state. The lithium battery can be charged and discharged freely. Since the on-resistance of the MOSFET is very small, usually Less than 30 milliohms, so its on-resistance has little impact on the performance of the circuit. In this state, the current consumption of the protection circuit is μA level, usually less than 7μA.

      2. Overcharge protection

      The charging method required for lithium batteries is constant current/constant voltage. In the early stage of charging, constant current charging is used. As the charging process progresses, the voltage will rise to 4.2V (depending on the positive electrode material, some batteries require a constant voltage value of 4.1V) , switch to constant voltage charging until the current becomes smaller and smaller.

      During the charging process of the battery, if the charger circuit loses control, the battery voltage will continue to be charged with constant current after it exceeds 4.2V. At this time, the battery voltage will continue to rise. When the battery voltage is charged to exceed 4.3V, the battery chemistry will Side reactions will be aggravated, causing battery damage or safety issues.

      In a battery with a protection circuit, when the control IC detects that the battery voltage reaches 4.28V, its "CO" pin will change from high voltage to zero voltage, causing V2 to turn from on to off, thereby cutting off the charging circuit. The charger can no longer charge the lithium battery, thus providing overcharge protection. At this time, due to the existence of the body diode VD2 of V2, the battery can discharge the external load through this diode. There is still a delay time between when the control IC detects that the battery voltage exceeds 4.28V and sends the shutdown V2 signal. The length of this delay time is determined by C3 and is usually set to about 1 second to avoid errors caused by interference. judge.

      3. Over-discharge protection

      When the lithium battery discharges the external load, its voltage will gradually decrease with the discharge process. When the battery voltage drops to 2.5V, its capacity has been completely discharged. At this time, if the battery continues to discharge the load, the battery will be damaged. permanent damage.

      During the battery discharge process, when the control IC detects that the battery voltage is lower than 2.3V (this value is determined by the control IC, different ICs have different values), its "DO" pin will change from high voltage to zero voltage, causing V1 From on to off, the discharge circuit is cut off, so that the battery can no longer discharge the load, which plays the role of over-discharge protection. At this time, due to the existence of the body diode VD1 of V1, the charger can charge the battery through this diode.

      Since the battery voltage cannot be reduced in the over-discharge protection state, the current consumption of the protection circuit is required to be extremely small. At this time, the control IC will enter a low power consumption state, and the power consumption of the entire protection circuit will be less than 0.1μA. There is also a delay time between the control IC detecting that the lithium battery voltage is lower than 2.3V and sending the shutdown V1 signal. The length of this delay time is determined by C3 and is usually set to about 100 milliseconds to avoid interference. Misjudgment.

      4. Overcurrent protection

      Due to the chemical characteristics of lithium-ion batteries, lithium battery manufacturers stipulate that the maximum discharge current cannot exceed 2C (C=battery capacity/hour). When the battery is discharged with a current exceeding 2C, it will cause permanent damage to the battery or safety issues. .

      During the normal discharge process of the battery to the load, when the discharge current passes through two MOSFETs connected in series, a voltage will be generated at both ends due to the on-resistance of the MOSFETs. The voltage value U=I*RDS*2, RDS is a single MOSFET conduction resistance, the "V-" pin on the control IC detects the voltage value. If the load is abnormal for some reason, the loop current increases. When the loop current is large enough to make U>0.1V (this value is determined by When the control IC determines (different ICs have different values), its "DO" pin will change from high voltage to zero voltage, causing V1 to turn from on to off, thereby cutting off the discharge loop and making the current in the loop zero. Plays the role of over-current protection.

      There is also a delay time between the control IC detecting the occurrence of overcurrent and sending the shutdown V1 signal. The length of this delay time is determined by C3, usually about 13 milliseconds, to avoid misjudgment caused by interference.

      5. Short circuit protection

      When the lithium battery is discharging the load, if the loop current is so large that U>0.9V (this value is determined by the control IC, different ICs have different values), the control IC determines that the load is short-circuited, and its "DO" pin It will quickly change from high voltage to zero voltage, causing V1 to turn from on to off, thus cutting off the discharge circuit and playing a role in short-circuit protection. The delay time of short circuit protection is very short, usually less than 7 microseconds. Its working principle is similar to overcurrent protection, but the judgment method is different and the protection delay time is also different.

      Lithium battery protection circuit design

      Due to the chemical characteristics of lithium batteries, during normal use, chemical positive reactions in which electrical energy and chemical energy are converted into each other are carried out internally. However, under certain conditions, such as overcharging, overdischarging and overcurrent will cause internal damage to the battery. A chemical side reaction occurs. When the side reaction intensifies, it will seriously affect the performance and service life of the battery, and may produce a large amount of gas, causing the internal pressure of the battery to rapidly increase and then explode, causing safety issues. Therefore, all lithium batteries need a protection The circuit is used to effectively monitor the charging and discharging status of the battery, and to shut down the charging and discharging circuit under certain conditions to prevent damage to the battery.

      Lithium-ion battery protection circuits include overcharge protection, overcurrent/short circuit protection and overdischarge protection. They require high precision in overcharge protection, low power consumption of the protection IC, high withstand voltage, and zero-volt rechargeability.


    Read recommendations:

    902030 500mAh 3.7V

    What are the core technologies of lithium battery pack Pack.industrial energy storage battery compan

    3.2v lifepo4 battery 320ah.About the development trend of new energy technology in the future

    3.7 volt 18650 lithium battery

    AG3 battery

    dry cell battery.Introduction to the advantages, disadvantages and technical parameters of lithium m

    Return to List

    AAA Carbon battery.Lithium-ion battery production and manufacturing process, lithium battery product

    Relevant News